Briggs and Stratton’s governor is a vital part of your lawnmower, no doubt. But when the Briggs and Stratton governor problems occurs, the lawnmower will become too slow or too fast. Sometimes it’s tough to find out the facts, and why they are troubleshooting over time.
You must have known that all combustion engines have 3-things to run. Fuel, fire, and compression are the three that can impact these issues. If the engine suddenly gets surge, try to inquire about the fact you’ve adjusted the governor righteously, as the governor will run through the lower speeds.
However, here are the other facts that may also cause this difficulty regarding these concerns.
Briggs And Stratton Governor Problems
A governor works to accelerate the engine speed. As it is related to minimizing and maximizing the speed of your engine power, the issue first you’ll face is whether it becomes too slow or too fast.
To fix this issue, you need to adjust the governor inside the engine. So the first thing you have to understand is why your engine is getting too slow. If you don’t find an adequate reason for this, then go and adjust it.
Before jumping into their details’ conversion, we would like to attach a small table to give a short hint. Allow these fixes to solve the problem of your Briggs and Stratton governor.
| Briggs and Stratton Governor Issues | Fixes To Try |
| Governor spring get worst | Replace it or try to repair the damage |
| the throttle linkage problem | Turn off the engine & move it back and forth several times |
| Damage or deadly coil & cylinder | Replace the cylinder |
| Older V-twins inside the pressed in stud | Settle the raising height & replace the governor gear |
| Small chunks broke out at the bottom of the cylinders | Clean up the crank using muriatic acid if there’s any aluminum transfer |
These are the five common issues that can make the governor run correctly. If the governor makes the way down when you’re in to cut out the grasses or climb on a hill, try to reverse the adjustment. What do you have to do? Let’s take a look.
Adjust The Briggs and Stratton Governor
First, you should try to fix the Briggs and Stratton 5hp governor problems and adjust it with the engine. First, check out the arm of the governor. Then loosen the arm as it will force the throttle to move freely. Afterward, pick a note in which direction the arm is moved when the throttle rotates inside it.
Let the governor’s arm be moved in the same direction once the throttle gets fully opened. Now hold the shaft when adjusting it to the new position. Then shut down the post and close it using the nut at the base of the arm. Finally, release it and check whether it moves freely or not. At last, reconnect the engine to the power to test the condition of your newly adjusted governor.
Do A Quick Compression Test
Your governor didn’t run swiftly if it had blown head gaskets/ bent push rods. In general, the engine will run too well on one cylinder until it gets loaded down. So you need to do a quick compression test there. A quick compression test here notifies you of making compression on both sides.
Commonly, the Briggs and Stratton governor issues occur for bent/blown head gaskets. Sometimes it has fallen out entirely out of position. As well, the coil can also get worse at a time and leave a dead cylinder.
Thus, it would help if you did not forget that if any part breaks or bends, you have no choice except replacing it all. Dead cylinders or bent gaskets, whatever you find there, try to modify or replace them as early as possible.
Check The Long Spring & Governor Lever
When you determine to move the hand control from idle/slow speed, the lever pull gets open in throttle directions. Briggs and Stratton governor springs get started to push the throttle closed when you switch on the engine. These things also happen when you adjust the governor to take the slack out of the mechanism.
To fix this, you should make the lever harder and increase the rpm that goes up. There you also find the bellcrank and governor lever, which get tight together on the governor rod.
So try to free all the linkages to be free to move without binding. By doing this, you will get a slope connecting to the governor lever and the throttle bellcrank. Also, It will help to lessen the long spring to pull the governor lever incorrectly.
Reset The Governor Settings
Resetting the governor setting is a primary setting, even if you face the problem of low rpm on your engine. Adjusting the governor inside the engine sometimes didn’t match with the lever to the carbs. For this, the engine doesn’t go back to stop, and it runs too fast. Again, it will turn the governor counterclockwise, even if you try to get it back.
So here, you need to reset the governor first. Just rotate the governor shaft in the same direction when you move the throttle shaft. Then tighten down the clamp on the governor’s arm.
If the engine didn’t turn on, pin the throttle to idle, as it had a failed governor gear. Again, the Briggs V twins are highly responsible for this failure. Simply stand up the tractor frames. Afterward, put 2*4 screws at its tip back. Then take off the bottom engine cover.
Repeat the same process for the Briggs and Stratton governor adjustment. Thus, you can now fix this problem.
A Helpful Tutorial You May Need!
Frequently Asked Questions (FAQs)
How to adjust the governor on Briggs and Stratton 8hp?
You must first identify where to pull the lever to open the throttle. When the engine speeds up, the internal governor mechanism tries to close the throttle. You can hold the selected speed once you’ve balanced it. When the small shaft is turned on, you will be able to exit the crankcase.
How do you know if the governor is bad?
It’s straightforward to find out if the governor gets toast. Just run the engine at ¾ throttle. Then figure out whether the government arm is applying pressure to the arm away from the carb. Try to pressurize it as much as it needs to push off the peninsula. If there is no pressure, then it’s a bad governor. Otherwise, it will let you adjust and work with the parts righteously, as well as the governor and throttle screws.
How do you reset the governor?
To resettle the governor, activate the solenoid at speed, it must be less than the usual overrate. Then set out the safety gears. Governors usually come at a standard 120-volt reset switch. So after activating the bags, set on the reset manual, and you’re all finished doing the task.
How do you adjust the governor on a Briggs and Stratton twin?
To adjust the Briggs and Stratton twin, set on the throttle to total capacity. Then move the governor shaft in the same direction when it gets traveled. Then hold it in the new position and tighten the nut at the base of the arm. Finally, check the throttle for whether it can move freely or not.
Bottom Line
Last but not least, the governor will accelerate the engine when the throttle opens. We won’t guarantee you that the above fixes will be workable for every concern. Because each of the vehicle components acts differently, it depends on how often you use them. In that case, we attach them here to give you hints to give a try before bringing it to any mechanical experts.
The good news is the strategies can solve the Briggs and Stratton governor problem within minutes, as mentioned above. Yet, it’s necessary to have a little knowledge to work with these types of affairs.
You Can Also Read:
- The Briggs and Stratton Carb Adjustment Diagram & Instructions
- The Briggs and Stratton Throttle Linkage Diagram
- Briggs And Stratton Governor Spring Diagram to Locate the Part
- Looking For Briggs and Stratton Governor Linkage Diagrams?
Was it helpful?
Enamored with the world of golf Jack pursued a degree in Golf Course Management at THE Ohio State University. This career path allowed him to work on some of the highest profile golf courses in the country! Due to the pandemic, Jack began Inside The Yard as a side hustle that quickly became his main hustle. Since starting the company, Jack has relocated to a homestead in Central Arkansas where he and his wife raise cattle and two little girls.